How to Install Storm Doors? [Step by Step Guide]

Installing a storm door is easy if you follow a few simple tips and steps.

  • First of all, you have to inspect the previous door and check if there is space in the adjoining wall for the new door.
  • Now you can place the door into sawhorses.
  • You might need to drill the holes if your door is of a design that requires installing new hinges.
  • Once you fix the screws on the door, you need to install the closing system.
  • Now you can tighten all the screws and fix all the gaps.

Let us take a detailed look at how to install a storm door. But before we start, let’s take a look at the tools and things you need to have before you start any installation process.

Have a look at this guide first, If you don’t know what are storm doors?

Required Tools for this Project 

It would be best if you had these important tools for installing a storm door before you start. It will save you time and disappointment.

  • 4-in-1 screwdriver
  • Caulk weapon
  • Hammer
  • Level
  • Pliers
  • Utility knife
  • Wood chisel
  • Combination square
  • Cordless drill
  • Hacksaw

Required Materials for this Project 

Save yourself from emergency shopping trips by having every one of your materials prepared early. Here’s a list of things you need to have before you start your storm door installation process.

  • 1/4-in. x 3/4-in. furring strip
  • Exterior caulk
  • Exterior paint
  • Shims
  • Storm door

Process of Installing Storm Doors:

How to install storm doors infographic

Step 1: Measure the Opening and Check the Doorjamb

The first step is to measure the opening to decide the appropriate door size to purchase. While measuring, you need to focus on the doorjamb, making sure the surrounding trim is strong, level and plumb.

Storm doors can be introduced to open to one side or the other side. You’ll see it easier to introduce your storm door with the goal that the handle is on the same side as the other door behind the storm door.

Step 2: Cutting the Hinge Frame and Removing the Glass

Imprint the pivot outline at a length 1/8″ not exactly that of the door frame opening. With the hacksaw, slice the pivot casing to measure.

The glass makes up a great level of the heaviness of the door. Eliminate the glass from the storm door before introducing it to make the whole process easy.

Step 3: Join the Hinge Frame and Hinges

Screw two screws in the pivot outline into the frames to hold the door set up. Connect pillar screws at every one of the pivots. Check the fit by opening and shutting the door. Wrap up getting the dribble cap by screwing it to the frame.

Step 4: Measure and Cut the Frame

Measure the lock side of the door frame and cut the edge 1/8″ less than the estimation.

Step 5: Add the Rubber Sweeps

Eliminate the expander sweep from the door. Slide the elastic compasses into the directions in the lower part of the door. Crimp the ends of the channels to hold the ranges set up.

Trim overabundance clear material, permitting a 1/8″ overhang on the sides. Reattach the expander, with the screw side looking in.

Step 6: Install the Doorknob

Your storm door may incorporate a design, which will assist you with figuring out where to drill your openings for the door equipment.

Drill the openings for your doorknob and lock, line up the handle and lock, and add them into the openings, starting with the outside pieces. At that point, embed the inside pieces, and screw them into place.

Deadbolt locks are coming with new storm doors these days. These are installed similarly to standard doorknobs.

Step 7: Install the Striker Plate and Stop Washer

Now you can install the striker plate and slide the stop washer into a closer place.

Step 8: Installing the Closer Unit

Installing the closer unit with sections on each end of the closer. Hold the closer level at the height suggested by the door manufacturer and imprint the section area on the door and doorjamb. Secure the closer to the door and doorjamb with screws.

Conclusion:

Installing a storm door is easy if you follow the above-mentioned steps. You can do it yourself with the proper tools and materials, which we have listed earlier in the article. Storm doors come in standard size and can fit into any home door.

Leave a Comment